RRAS Audits
Applies To: Windows Server 2008 R2
The Routing and Remote Access service has determined that RRAS audits generated an audit entry when a system event was executed successfully. These events confirm successful Routing and Remote Access operations.
Events
| Event ID | Source | Message |
|---|---|---|
RemoteAccess |
The user: %1 has connected and has been successfully authenticated on port: %2. | |
RemoteAccess |
The user: %1 connected on port: %2 on: %3 at: %4 and disconnected on: %5 at: %6. The user was active for: %7 minutes, %8 seconds. %9 bytes were sent and %10 bytes were received. The port speed was: %11. The reason for disconnecting was: %12. | |
RemoteAccess |
The user: %1 on port: %2 was called back at the number: %3. | |
RemoteAccess |
The remote access server acquired IP address: %1 | |
RemoteAccess |
The port: %1 has been disconnected due to inactivity. | |
RemoteAccess |
The port: %1 has been disconnected because the user reached the maximum connect time allowed by the administrator. | |
RemoteAccess |
The user: %1 has connected and has been successfully authenticated on port: %2. Data sent and received over this link is encrypted. | |
RemoteAccess |
The user: %1 has connected and has been successfully authenticated on port: %2. Data sent and received over this link is strongly encrypted. | |
RemoteAccess |
The user: %1 has successfully established a connection to: %2 using the device: %3. | |
RemoteAccess |
The connection to: %1 made by user: %2 using device: %3 was disconnected. | |
RemoteAccess |
The user: %1 successfully established a connection to: %2 using the device: %3. This connection happened automatically because the bandwidth utilization was high. | |
RemoteAccess |
The remote access server established a connection to: %1 for the user: %2 using the device: %3. This connection happened automatically because the bandwidth utilization was high. | |
RemoteAccess |
The connection to: %1 made by user: %2 using device: %3 was disconnected. This disconnection happened automatically because the bandwidth utilization was low. | |
RemoteAccess |
A link in the connection to: %1 made by user: %2 should be disconnected. The bandwidth utilization is too low. | |
RemoteAccess |
Interface: %1 is now reachable. | |
RemoteAccess |
Because no certificate has been configured for clients dialing in with EAP-TLS, a default certificate is being sent to user: %1. Go to the user's remote access policy and configure the Extensible Authentication Protocol (EAP). | |
RemoteAccess |
The user: %1 connected on port: %2 on: %3 at: %4 and disconnected on: %5 at: %6. The user was active for: %7 minutes %8 seconds. %9 bytes were sent and %10 bytes were received. The reason for disconnecting was: %11. | |
RemoteAccess |
The user: %1 connected on port: %2 has been assigned address: %3 | |
RemoteAccess |
The user with IP address: %1 has disconnected. | |
RemoteAccess |
The user: %1 has connected and has been successfully authenticated on port: %2. | |
RemoteAccess |
The user: %1 connected on port: %2 on: %3 at: %4 and disconnected on: %5 at: %6. The user was active for: %7 minutes, %8 seconds. %9 bytes were sent and %10 bytes were received. The port speed was: %11. The reason for disconnecting was: %12. | |
RemoteAccess |
The user: %1 on port: %2 was called back at the number: %3. | |
RemoteAccess |
The port: %1 has been disconnected due to inactivity. | |
RemoteAccess |
The port: %1 has been disconnected because the user reached the maximum connect time allowed by the administrator. | |
RemoteAccess |
The user: %1 has connected and has been successfully authenticated on port: %2. Data sent and received over this link is encrypted. | |
RemoteAccess |
The user: %1 has connected and has been successfully authenticated on port: %2. Data sent and received over this link is strongly encrypted. | |
RemoteAccess |
The user: %1 has successfully established a connection to: %2 using the device: %3. | |
RemoteAccess |
The connection to: %1 made by user: %2 using device: %3 was disconnected. | |
RemoteAccess |
The user: %1 connected on port: %2 on: %3 at: %4 and disconnected on: %5 at: %6. The user was active for: %7 minutes %8 seconds. %9 bytes were sent and %10 bytes were received. The reason for disconnecting was: %11. | |
RemoteAccess |
The user: %1 connected on port: %2 has been assigned address: %3 | |
RemoteAccess |
The user with IP address: %1 has disconnected. |