Partager via

Windows CE Boot Loader Output for the Intel DBPXA250 Development Platform

  • Article

The following text shows the Windows CE boot loader output for the Intel DBPXA250 development platform.

Beginning System Initialization SDCLK[1] = MemClk MemClk = 99.53 MHz Run Mode = 2 * MemClk Turbo Mode = 2 * Run Mode Mode: TURBO

Beginning SDRAM Scrub...
SDRAM Scrub Complete

**************************************************** **************************************************** **************************************************** **************************************************** **************************************************** OEMInitDebugSerial using UART1

Microsoft Windows CE Ethernet Bootloader Common Library Version 1.0 Built Feb 13
 2003 18:44:47
Copyright (c) 2000-2001  Microsoft Corporation
Microsoft Windows CE Ethernet Bootloader 3.3 for the Intel DBPXA250 Development
Platform (Built Feb 15 2003)
Press [ENTER] to download now or [SPACE] to cancel.

Initiating image download in 0 seconds.
Checking for SMC 91C96 Ethernet controller...
Entering SMCInit
SMC Ethernet card detected at I/O base 0xBF500000
SMC MAC Address: 0:2:179:146:165:26
SMC Ethernet card Config_Reg=20B1
SMC Ethernet card Config_Base=1867
SMC Ethernet card Switch=3F
SMC config reg val: 000032B1
SMC Reset complete2
SMC 91C96 Ethernet controller initialized.
System ready!
Preparing for download...
INFO: Using device name: 'XSC1BD42266'
InitDHCP():: Calling ProcessDHCP()
ProcessDHCP()::DHCP_INIT
Got Response from DHCP server, IP address: 10.199.14.143
!CheckUDP: Not UDP (proto = 0x00000001)

ProcessDHCP()::DHCP IP Address Resolved as 10.199.14.143, netmask: 255.255.252.0
Lease time: 259200 seconds
Got Response from DHCP server, IP address: 10.199.14.143
No ARP response in 2 seconds, assuming ownership of 10.199.14.143
+EbootSendBootmeAndWaitForTftp
Sent BOOTME to 255.255.255.255
Sent BOOTME to 255.255.255.255
Sent BOOTME to 255.255.255.255
.
.
.

If you press the SPACEBAR to break into the configuration menu, you will see the following output:

Beginning System Initialization SDCLK[1] = MemClk MemClk = 99.53 MHz Run Mode = 2 * MemClk Turbo Mode = 2 * Run Mode Mode: TURBO

Beginning SDRAM Scrub...
SDRAM Scrub Complete

**************************************************** **************************************************** **************************************************** **************************************************** **************************************************** OEMInitDebugSerial using UART1

Microsoft Windows CE Ethernet Bootloader Common Library Version 1.0 Built Feb 13
 2003 18:44:47
Copyright (c) 2000-2001  Microsoft Corporation
Microsoft Windows CE Ethernet Bootloader 3.3 for the Intel DBPXA250 Development
Platform (Built Feb 15 2003)
Press [ENTER] to download now or [SPACE] to cancel.

Initiating image download in 3 seconds.


Ethernet Boot Loader Configuration:

0) IP address: 192.168.80.2
1) Subnet mask: 255.255.0.0
2) Boot delay: 5 seconds
3) DHCP: Enabled
4) Reset to factory default configuration
5) Download new image at startup
6) Program RAM image into FLASH: (Disabled)
7) Program SMSC MAC address
8) Boot device order: SMSC -> PCMCIA -> CF
9) Check image signature(s): (Disabled)
D) Download image now
F) Format flash (will not overwrite eboot or eboot parameters)
L) Launch existing flash resident image now


Enter your selection:

See Also

How to Use the BSP for the Intel XScale DBPXA250 Development Platform

Last updated on Wednesday, April 13, 2005

© 2005 Microsoft Corporation. All rights reserved.